W 2.1″ x D 3″ – 10 ft lengths
·Rugged design to withstand heavy impact, these rub rails are built to last.
·Will not crack, rot or deteriorate when exposed to temperature extremes.
·UV inhibitor prevents yellowing and discoloring from sunlight.
·Unaffected by oil, gas or saltwater.
5002 – EXCELLENT VALUE
W 2.4″ x D 3.5″ – 10 ft. lengths available in white or black
·Rugged design to withstand heavy impact, these rub rails are built to last.
·Will not crack, rot or deteriorate when exposed to temperature extremes.
·UV inhibitor prevents yellowing and discoloring from sunlight.
·Unaffected by oil, gas or saltwater.
P BUMPER- A BOAT FENDER AROUND YOUR DOCK
W 4″ x D 3.75″ – 8 ft lengths
·Air-cushion profile – a complete system using connectors, end plugs and 90 degree corners.
·Constructed of marine grade flexible PVC, developed not to chip or crack under normal usage.
·Unaffected by oil, gas or salt water. UV inhibitors and fungicides prevent fading, yellowing, deterioration from sunlight and unsightly blotching.
·Bright white finish enhances your dock’s appearance.
·Easily installed on any horizontal or vertical surface.
PERIMETER BUMPER – SUPERIOR CUSHIONING PROTECTION.
W 5 ¾” x D 2 ¼” – 3′, 6′, and 9’ lengths
·Designed to solve the ever present problem or marring or scratching that occurs with many rubber type bumpers.
·Constructed with a heavy duty polyester fabric encasement – guaranteed not to deteriorate in the sun.
·Special closed cell inner cushion provides superior and long-lasting impact protection for your boat.
·Flexible construction allows vertical, horizontal, rounded or flat surface installation.
·Tab system allows standard “top of dock” or unique “fold over” mounting which conceals the top row fasteners and allows quick and easy installation.
·Cleans easily with liquid soap.
Dock Cleats
OPEN BASE ALUMINUM CLEATS
·Cast aluminum cleats are sand blasted to give a clean gray matte finish.
·Each cleat is designed with an extra wide footprint for added strength.
·Enlarged counter-sunk hole for easy installation with a socket.
·Can be through bolted or lag bolted.
·8” x 3.5” x 2”
SMALL BOAT ALUMINUM CLEATS
Compact 3″ natural aluminum or powder coated black or white, these safety cleats are excellent for tying up canoes, small fishing boats, and pedal boats.
SAFETY CLEATS
·All aluminum heavy duty commercial fold-down cleat.
·Available in natural aluminum and Black or White powder coat finish.
·Available in 6” for boats up to 18’ and 8” for larger boats.
FLIP UP CLEATS
·Cast aluminum powder coated white flip-up cleat.
·Distinctive and highly functional.
·Available in 3 sizes – 3”, 6” and 8”
NYLON FLIP UP CLEATS
·Nylon composite fold down cleat which mounts to any surface.
·Large footprint for added strength.
·Rated for ½” rope.
·Dimensions 9.9” x 6.5”
·Tensil strength 27,000 psi
·Available in black or white
Dock Ladders
HEWITT ALUMINUM 4 STEP
All Aluminum Easy Swing-Up
·Strong one piece
·Extruded slip resistant steps
·Swing up onto dock when not in use or for winter
·Complete with hinge and hardware
GALVALUME WHITE POWDER COAT
Good Value & Good looking
·Heavy duty ladder featuring 1- 1/2” galvalume tubing and white polyester powder coated for a bright, clean looking finish.
·Lower section can easily be removed with two bolts for off season storage.
·Available in 3 and 4 step models.
ROTO-MOULDED FLIP UP
Tough and durable
·4 step polyethylene
·This roto-molded ladder swings up and out of the way, locking in place when not in use
·Will not corrode with exposure and will not fade or crack
·Molded-in UV inhibitors and fungicides
STAINLESS STEEL
Upscale
·Brushed stainless steel finish for an elegant sheen and upscale finish.
·Strong 1 ½” tubing provides a secure grip.
·The lower section can easily be removed with two bolts for off season storage.
·Available in 3 and 4 step models.
STAINLESS STEEL FLIP
Upscale and flip-up legs
·Brushed stainless steel finish for an elegant sheen and upscale finish.
·Strong 1 ½” tubing provides a secure grip.
·Hinged design allows the ladder to conveniently flip out of the water when not in use.
·Locks securely in both positions.
·4 step.
STEEL LADDER
Angled
Comes in two finishes; blue powder coat and galvanized (silver finish), and three sizes- 3 step, 4 step, and 5 step. Powder coat provides a tough, durable finish. Steps are galvanized and powder coated for extra protection. Galvanized version protects against rust and corrosion in salt water.
Optional Speed Release available for easy removal from dock.
GALVANIZED STEEL QUICK RELEASE
Option for easy removal of steel ladder from dock.
Mooring Whips
MOORING ARMS – Economical protection
·Easy to install mooring arms apply vector based forces to the bow and stern of the watercraft allowing it to freely and effortlessly follow wave and water action yet securely keep the craft at arms length from the dock.
·Manufactured from the same durable cross-wound fiberglass as mooring whips, each set includes polyethylene line and pivot retainers as well as stainless steel hardware.
·Hot dipped galvanized cleats and mooring lines are included.
·Available in 4 ft. and 6 ft. lengths for PWCs to mid sized cruisers up to 5000 lbs.
PREMIUM MOORING WHIPS – Fixed Angle Base
·Exclusive “Plug & Socket” design for quick and easy separation.
·Tie off cleat and new carbon fiber technology.
·Solid cast aluminum base with built-in cleat, ring and thumb screw.
·Unique tip with functional roller and tie off cleat for easier boat access – simply release the whip line from the tie off cleat. The whip lines effortlessly roll through the pulley at the tip causing the boat to gently approach the dock for boarding.
·Double braided nylon whip lines, spring lines and unique line tensioner for one-handed set-up.
·Available in 8’, 12’, 14’ and 16’ lengths for boats from 18’ to 33’ and up to 20,000 lbs.
ULTIMATE MOORING WHIPS – Rocker Bases for Boats with Towers
·Solid fiberglass rod with an exclusive cross-wound fiberglass for extra rigidity, strength and flex.
·Rocker bases allow these whips to retract almost completely for clearance for boats with towers. No more jostling the controls to avoid whips protruding over the edge of the dock.
·Exclusive “Plug & Socket” design for quick and easy separation and cast aluminum base with built-in cleat, ring and thumb screw.
·Each whip includes functional roller tip and a tie-off cleat for easier access to your boat.
·Stainless steel mounting hardware is included.
·Available in 12’, 14’ and 16’ sizes for watercraft from 21’ to 33’ and up to 20,000 lbs.
Mooring Buoys
24″ MOORING BUOY WITH SHACKLE POCKET
The impact resistant high density polyethylene shell is 3/16″ thick filled with expanded polystyrene foam for the most reliable flotation. Thick wear resistant polyethylene tube is molded into the shell. Washer ring is included to support the shackle and ground tackle. All buoys have a two year warranty.
INFLATED MOORING BUOY
This Mooring Buoy has been designed to provide the ultimate in strength, durability and boat protection, giving increased security to any mooring.
·Mooring Iron made with vinyl protected galvanized steel
·Large reinforced 4-3/8″ eye and 1-1/2″ swivel
·Soft vinyl surface protects boat finishes
·Polyform’s unique vinyl valve seals securely
·Even wall thickness for maximum strength and durability
·Limited three year warranty
·Available in 13.5” x 18” and 17” x 22”
Dock Hardware
FEMALE OUTSIDE CORNER
Has two 1/2″ welded tabs. Use with male outside corner to connect docks end to end. Each leg is 10″ L x 5″ H. Joint requires bolt set or Connector pin Set.
MALE OUTSIDE CORNER
Has one 1/2″ welded tab. Use with female outside corner to connect docks end to end. Each leg is 10″L x 5″H.
OUTSIDE CORNER END
Use this corner at ends of fingers and docks. Ideal for swim floats. Each leg is 10″L x 5″H.
INSIDE CORNER
This heavy-duty inside corner should be used with one of the outside corners. Each leg has elongated holes for easy fit-up and is 8 1/2″L x 5″H.
FEMALE T CONNECTOR
Has two welded 1/2″ tabs. Bolts to side of dock to attach fingers and ramps. 5″L x 5″H
MALE T CONNECTOR
Has one welded 1/2″ tab. Use with female T connector to attach fingers and ramps. 5″ L x 5″ H. Bolt set of Connector pin set required.
CONNECTOR PIN SET
For quick disconnect. Used to connect male and female T connectors. Galvanized 3/4″ connector pin and hitch clip pin.
BACK UP PLATES
5″ x 5″ reinforcing plates are used to back up the single T males and females.
WASHER PLATE
Use two washer plates with each angle. Measure 1-1/2″ L x 5″ H.
ANGLE BRACKET
Use this heavy-duty angle for all cross supports. Each leg measures 2-1/2″L x 5″H.
INSIDE CORNER W/PIPE HOLDER
These heavy-duty inside corners should be used with one of the outside corners and as an internal pipe holder to give strength to the dock’s frame. Measures 8-1/2″ L x 5″H. Requires carriage bolt set for attaching. Available in either 2″ or 3″ pipe sides.
OUTSIDE PIPE HOLDER
Bolts to outside of dock. Carriage bolt set required for attaching. Use 2″ pipe to hold dock in plate.
HEAVY DUTY ROLLER ASSEMBLY
Bracket and roller bolt directly to the Deck Plate and can be added to aid up and down motion of the dock. 6″ roller turns on a 5/8″ diameter shaft. 3/8″ bracket is hot-dipped galvanized.
INSIDE ROLLING RAMP BRACKET
5″ x 11″ x 1/4″ galvanized steel inside rolling ramp bracket includes left and right ramp brackets.
CHAIN RETAINER
Bolts to side of dock. Use weights and chains to hold dock in place. Accommodates 1/4″, 3/8″ and 1/2″ chain. Measure 5″L x 5″H.
Dock Floats
PREMIER COMMERCIAL DOCK FLOATS – The floats chosen by professional dock builders.
“The most important component of your floating dock is the flotation that keeps the dock floating.”
Premier foam-filled float drums offer durable flotation for new or existing dock systems.
The plastic exterior one-piece seamless shell design prevents leakage and separation caused by weak joints. The drum wall is made of tough virgin polyethylene with ultra violet inhibitors to prevent damage from the sun, debris, oil, gas, marine organisms, salt, and fresh water. A nominal wall thickness of .150 offers a stronger, more durable float. The top of the shell is flat with molded-in mounting slots for easy attachment to any dock frame.
The interior of the float drum is filled with expanded polystyrene (EPS) foam. The foam is steam pressured for a tight fit that provides the highest buoyancy possible. The foam interior provides floatation if the outside shell becomes punctured and is continually tested to meet or exceed the Hunt Water Absorption Test standard of 3 lbs per cubic foot.
Premier’s warranty is unmatched! Confident in their tested dock float quality and field-tested design, Premier floats are backed by the only 15-year warranty in the industry, 100% non-prorated replacement for the first 10 years.
With over 50 different sizes available from one to four feet wide, three to eight feet long and eight to thirty-two inches high, you are sure to find a float that fits your needs.
Solar Lights
Pro Dock Lite – LED
Heavy Duty Construction and Style.
Automatic on at dusk.
Perfect for
•Dock
•Walkways and Decks
•Landings
•Durable, Weatherproof
•Rechargable Replacable batteries.
Post Solar Lites
•Powerful solar charging performance
•6 Preinstalled LED colors change with a flip of a switch
•Easy twist-on lid with large rubber seal
•360° lenticular light diffusing lens and domed reflector maximize light output
•Installs easily with no wires
•Fits post sizes 1-5/8″, 1-7/8″, 2-3/8″, and 3-1/4″ ID posts, universal flat surfaces with included adaptors.
•Rechargable Replacable batteries.
Benches
4 Ft. and 6 Ft Outdoor Benches
·The outdoor dock/lawn benches feature arms with molded in beverage holders!
·All benches are designed using a combination of traditional and contemporary styling, embodying strength, beauty and elegance.
·Clean lines and pure simplicity of design find itself at home anywhere.
·Constructed of 100% weatherproof polyethylene.
·Available Colors: Pebble Beach (White) or Desert Sand (Beige)
Offset Bench
·All aluminum construction, these benches are unique when mounted to the dock.
·The bench is over the water, not on the deck, leaving that important deck space.
·Available in 4 feet and 8’ feet
·Aluminum or cedar panels
·Bench armrests with cupholders optional
·Umbrella optional
Free Standing Bench
·All aluminum brackets, mounts to any flat surface
·Available in 4 feet and 8’ feet
·Aluminum or cedar panels
·Bench armrests with cupholders optional
·Umbrella optional
Bench Umbrella
·Aluminum construction, mounts to the back of bench.
·Used to shade the sitting area of your bench.
·32” of height adjustment.
·Standard vinyl or SeaMark fabric each available in 7 popular colors.
Bench armrest with cup holder
·Large 5” x 13 ½” molded armrest has deep cup holders that are rotational and can hold up to a 3 ½” diameter cup.
Kayak Racks
KAYAK RACK
·A sturdy and stylish kayak rack is a great solution for waterfront storage.
·Features molded-in kayak hook receivers to secure kayak to rack.
·Attaches to Wave Armor docks or special brackets available for mounting to truss or wood docks.
CRUISER KAYAK
The CRUIZER kayak has amazing stability and is perfect for the beginning paddler.
Cruizer kayaks are fun and comfortable, recreational sit-on-top style kayak, designed for paddlers of all ages and abilities. The unique high-speed hull design offers outstanding performance, excellent stability, and is virtually indestructible. This kayak is easily paddled and glides effortlessly through the water. Designed for use on lakes, ponds, and slower moving rivers.
Great features:
Tough & Weatherproof, Polyethylene construction,
Sit-on-Top Style Design for all ages & abilities
Molded-in beverage holder & foot rests
High-Speed Hull reduces drag
Molded-in Front & Rear Handles
3-Year Warranty
Weight: 35 Lbs
Weight Capacity: 185 Lbs Dimensions: 8′ 6″ L x 30″ W x 15″ D
Available Colors: Yellow, Blue
IMPULSE KAYAK
The IMPULSE kayak is the perfect day long adventure. Pack a cooler and you’re good to go!!
The Impulse Kayak is a fun and comfortable recreational, sit-on-top kayak, designed for paddlers of all ages and abilities. It’s unique high-speed hull design offers outstanding performance, excellent stability, and is virtually indestructible. Easily paddled, is perfect for use on lakes or slow moving rivers.
Great Features:
·Tough & Weatherproof, Polyethylene Construction
·Foam / Neoprene Seat Cushion with Adjustable Back Rest
·Spacious Cock Pit
·High-Speed Hull
·Molded-in Rear Compartment with Molded-In Tie Downs
·Molded-in Beverage Holder
·Molded-in Foot Rests
·Molded-In Finger Grips on Both Sides
·Molded-In Handles on Each End
Weight: 45 Lbs
Weight Capacity: 300 Lbs
Dimensions: 10′ L x 31″ W x 10″ D
Available Colors: Yellow, Blue
KAYAK PADDLE
·7-1/2” x 19” blade Dimension/ 1-1/8” Shaft Diameter
·Available in 7, 7-1/2 and 8 foot lengths.
·Snap button for easy assembly, disassembly and storage.
·Super strong aluminum shaft fully extends into the blade length for internal reinforcement and pre-installed drip rings.
·Take down coupling feature allows the blades to run parallel or feathered 90 degrees by simply depressing the spring-loaded button and turning the shaft ¼ turn.